thebigvilla.blogg.se

Wet dry wet guitar rig diagram
Wet dry wet guitar rig diagram











wet dry wet guitar rig diagram wet dry wet guitar rig diagram
  1. WET DRY WET GUITAR RIG DIAGRAM HOW TO
  2. WET DRY WET GUITAR RIG DIAGRAM FULL
  3. WET DRY WET GUITAR RIG DIAGRAM PLUS

WET DRY WET GUITAR RIG DIAGRAM HOW TO

Zed, do you hope you helped me? You are kidding? You just helped me too much, I don't know how to thank you! By the way, could you also send me how the fractal preset scheme would look? I'm sorry to ask you this again, but it's because I'm really stuck with this! I would like to have a few beers with you, but we are far away, too bad! Here are the pictures of my equipment! Hugs and thank you again for your attention !!

WET DRY WET GUITAR RIG DIAGRAM PLUS

It's possible? Could you send me the schematic of this type of connection again using the fractal ax fx 3, plus the matrix power, plus the plexi amp, plus three 4x12 boxes? Schemes with and without pedals. I saw that it is also possible for me to use my fractal and my matrix power together with my plexi amplifier, plus three 4x12 boxes to make that connection! If it is not uncomfortable for you, I would like to ask you again for the favor of teaching me how to make this connection, using the matrix power for wet (left and right) connected in two 4x12 marshall boxes (left and right) and the amplifier marshall plexi plus a 4x12 box as dry. My friend Zed, how are you? I hope you're well! I am thinking and researching a lot about the ways to make the wet / dry / wet bond. This means that if your overal Volume control is set low, then you're going to have a very quiet signal coming out of your effects loop, and you'll have to basically max out your external poweramp to match the 5150 III's volume.īasically the 5150 III should have an overall Master Volume control but it doesn't, and the end result is that for w/d/w setups, you have to crank your external poweramps to run at pretty much max volume so they match the output level of the 5150 III's poweramp.

wet dry wet guitar rig diagram

WET DRY WET GUITAR RIG DIAGRAM FULL

The way the 5150 III works is that each channel's Volume knob is technically a Channel Volume control, located in the circuit before the effects loop, and the poweramp is always running at full power.Īs for the Effects Loop, each channel's Volume control is in the circuit before the effects loop, meaning each Volume control doubles as an Effects Send volume. Unfortunately that's just how the amps are designed. I've also setup my 50 watt and 100 watt 5150 III's in w/d/w setups and got the exact same result as you. Once again, I thank you very much, hugs and good sound !! The expression pedals, should I connect them to the fractal or RJM 22? In balanced outputs output 1, can I turn on my matrix power and send the signal to my audio monitors?Ĭan I connect the BOSS Waza Tube Expander attenuator to the amplifier (wet / left - marshall plexi)? This attenuator has loop and MID input and output and some effects, I would like to control the effects contained in the attenuator also through RJM 22, where should I connect the MID of the attenuator, in the effect gizmo or in the ax-fx3 itself? When I do my presets on the fractal, should I disable the power and box emulations? However, can I use the preamp emulations?

wet dry wet guitar rig diagram

However, if I am not going to pester you, can you still answer some questions that I still have?īy the way, I will follow your recommendation and I will use RJM 22. I'm an amateur guitarist, I just play in my room (small studio) here at home. I'm not an expert on the fractal ax-fx 3 yet. I appreciate if you or friends can help me, hugs! What outputs and inputs should I use when presetting the fractal ax-fx3? I don't intend to use another guitar, as you are using in input 3, however, I want to use some more pedals! What could you suggest to me? With a connection like your Zed, can I use the FC-12 pedal (faslink II or Mid) or do I necessarily have to use the RJM 16 or 22 or another Mid pedal? I have some doubts and if you or someone can help me, I really appreciate it! I would like to use marshall plexi as wet (left side) and vox ac 30 as dry and marshall JVM as wet (right side). My equipment: ax-fx3, power matrix, vox ac 30, marshall plexi super lead with marshall 4x12 vintage box and marshall JVM410HJS also with marshall 4x, bozz waza tube expander (to use it with plexi), gizmo audio effect loop switching and some pedals. Zed, I've been wanting to make a wet / dry / wet system for some time, and I saw your scheme and it helped me a lot! Hello Zed and friends! I am from sao paulo Brazil.įirst of all, my English is very bad, sorry for that!













Wet dry wet guitar rig diagram